Main features:
lOptimizing the two-axis high efficiency cutting mode, the efficiency is increased by about 80% compared with single machine.
lPrecision imported ball screw, linear guide, Y-direction grating ruler closed-loop control, high-precision machine for a long time to maintain.
lTouch teaching GUI, simulation display of editing process, multi-slice pre-cutting mode, simple and convenient program editing.
Advanced functions:
pMulti-piece double-knife cutting with the same disc;
pStepped Cutting (Double Cutter Slotting and Cutting) Mode;
pFault self-correcting function, multi-position detection;
p*Factory Automation Module;
Application:
It is mainly used for automatic cutting of QFN, DFN, BGA, LED-PCB frame, optical communication devices and other fields. It is suitable for quartz glass, alumina, ceramics, PCB board or package frame and other materials.
Low pressure, water pressure, worktable servo, turntable servo, spindle drive, altimeter system, control system fault alarm, operation chamber door safety lock, leakage detection, spindle current monitoring, vacuum insufficient protection function.
Maximum working size |
mm |
ø 12"or 290mm×290mm square |
||
Xaxis
|
Machinable range |
mm |
290 |
|
Feed speed input range |
mm/s |
0.1 - 600 |
||
Yaxis
|
Machinable range |
mm |
290 |
|
Single step intake |
mm |
0.0001 | ||
positioning accuracy |
mm |
0.003 within/300, 0.002 two with in/5 |
||
Zaxis
|
Effective travel |
mm |
40(ø2 "When cutting the blade) |
|
Mobile resolution |
mm |
0.00005 |
||
Repetition precision |
mm |
0.001 |
||
Maximum cutting blade diameter for use |
mm |
ø 58 |
||
Theta axis |
Maximum angle of rotation |
deg |
380 |
|
|
Angle accuracy |
″ |
15 |
|
principal axis
|
Rated output power |
kW |
1.8(or 2.4) at 30,000 min-1 |
|
Rated torque |
N・m |
0.48 |
||
Rotation number range |
min-1 |
3,000 - 60,000 |
||
The maximum framework to be used |
- |
12 inch or 290mm×290mm square |
||
Other Specifications
|
Power Supply |
v |
Three-phaseac380v±Ten% In addition to the above, the transformer needs to be configured |
|
Power consumption |
Processing time |
kW |
1.8(reference value) |
|
Warmer time |
kW |
1.2(reference value) |
||
Max Power consumption |
kVA |
5.5 |
||
Compressed air supply pressure |
Mpa |
0.5 - 0.8 |
||
Maximum compressed air consumption |
L/min(ANR) |
250 |
||
Cutting water pressure |
Mpa |
0.2 - 0.4 |
||
Maximum consumption |
L/min |
6.0 |
||
Cooling water pressure |
Mpa |
0.2 - 0.4 |
||
Maximum consumption |
L/min |
3.0 ( in 0.3 MPa ) |
||
Exhaust air volume |
m3/min |
1.5
|
||
Equipment size (W×D×H) |
mm |
1,080×1,330×1,800 |
||
Equipment weight |
kg |
about 1,000 |
Conditions of use:
1. please set the machine in a 20~25 C environment (the range of fluctuation is within + 1 c); the indoor humidity is less than 80%, and there is no condensation.
2. please use the air pressure dew point below -15 C, the residual oil is 0.1ppm, the filtration degree is above 0.01um/99.5, clean compressed air.
3., please control the water temperature of the cutting water at room temperature of +2 C (within the range of + 1 c), and the water temperature of the cooling water is the same as that of the room temperature (the fluctuation range is controlled at + 1 degrees Celsius).
4. please avoid the gravity impact of the equipment and any vibration threat from the outside world. In addition, please do not install the equipment near the blower, the vent, the high temperature device and the oil producing device.
5. please install the equipment in a waterproof floor and a place with drainage treatment.
6. please do the operation in strict accordance with the instructions of the company's products.
ChangShu:
TEL:+86-512-5296-9660
PHO:+86-139-1043-2532 Sam Yang
ADD:Changshu Economic & Technological Development Zone
Email:jcxj_support@163.com
Web:http://www.jcxj.com.cn